You are here
  • Elite Fuser Glass Kiln

  • Elite
  • £6,285.60 inc. VAT

    £5,238.00 exc. VAT

  • Add to Basket

  • Add to Wishlist

The Hobbyfuser and Pro-fuser sit at the pinnacle of their respective market sector in build quality, performance and reliability and the Elite-fuser now does the same in its own sector.

Creative Glass Guild offer the Elite Fuser with Free UK delivery and a £100 Voucher for Fusing Glass.

Features include

  • Internal size 1020mm x 800mm x 320mm
  • Power 10kw single phase OR three phase and neutral.
  • Quartz tube, Kanthal A1 "infra-red" element technology.
  • Angled and spring assisted viewing / vent ports in front chamber wall.
  • Optional automatic and programmable motorised roof vents.
  • Kilncare's unique breathing Stainless Steel slatted roof.
  • Stainless Steel roof, chamber and base.
  • High load, breathable and expanding walk mesh under floor.
  • Recessed floor.
  • Gas Strut lid lift assistance.
  • KCR32, 32 program, 32 segment controller.
  • Solid State Relay rapid response control.
  • High performance relay heat sink.
  • Ultra-fast response Inconel thermocouple.
  • KCR32 integral mounted.
  • 36 month guarantee on ALL parts including the elements.

The floor of the Elite-fuser is made from high grade, lightweight insulation bricks that give both a structurally steady surface to place the work on and a thermally steady base to aid in maximum glass results.

Under the floor is where the Elite-fuser excels. Under the brickwork, the floor structure is made from heavy duty walk mesh that expands with heat without distorting, offers superb physical strength and breathes, so, as with the roof of the kiln, helps and aids cooling dramatically.

As the bricks are not cemented in, they are easily replaced if required.

The elements are wound with Kanthal A1, renowned as the worlds best element wire. The elements are inside quartz tubes and the quartz tube element system we use is widely known as "infra-red" kiln heating.

The heating system is in the roof only.

Unlike other manufacturers, the element system in the Elite-fuser is fully covered under the kilns 36 month all parts guarantee.

The boards that make up the chamber are specially produced for the Elite Fuser and are pre-fired to 1100c before inserted into the kiln to remove any shrinkage or warping that could otherwise happen.

The KCR32 is multi-program controller targeted towards glass use with 32 programs each of up to 32 segments. Each segment is a controlled heating/cooling ramp followed by a soak. It is supplied pre-programmed with 9 typical glass programs (which can be over-written).

 

FEATURES:

• 32 programs - each with up to 32 segments
• Each segment is a controlled heating/cooling ramp soak
• Suitable for glass or ceramics use
• Soak times up to nearly 100 hours
• Ramp rates from 1 to 999°C/hour full
• Programs can be reviewed or altered while firing
• Program Pause & Segment Advance facilities
• Keyboard lockable
• Delayed start facility - up to 4 days
• Power failure recovery
• Energy used display
• Event / Damper / Fan relay output
• Alarm relay with alarm buzzer
• Mains power switch


Other details

The Elite-fuser is on lockable castors.

The lid seal is not stuck on but is held in by a removable stainless steel picture frame and as such, in the event of damage, it is fully replaceable leaving a factory fitted finish that will give years more trouble free use.

Each Elite-fuser is fired to 800c with its own KCR32 programmer before dispatch to ensure perfect operation, calibration and removal of most of the binder vapors that are released by all kilns on the first firing.

 

Customers who bought this product also purchased...

Can't find what you are looking for? Call our expert team today on +0044 (0)117 95 888 20